SVAT Electronics Security Camera CVQ1000 User Manual

User's Manual  
Model No. CVQ1000  
WIRED COLOR CAMERA WITH QUAD  
PROCESSOR & REMOTE CONTROL  
PLEASE READ CAREFULLY AND SAVE  
This manual contains important information about this product's operation. If you  
are installing this product for use by others you must leave this manual -or a  
copy-with the end user.  
 
Parts Included with This System  
1. 4 Channel Switcher Box  
2. Remote Control  
3. Color Camera With Mounting bracket  
4. 60ft Cable  
5. Video Cable  
6. 12V DC Adaptor for the Switcher  
x 1 set  
x 1 pc  
x 4 pcs  
x 4 pcs  
x 1 pc  
x 1 pc  
Parts of the System  
Parts of the Camera  
A. Mounting bracket  
B. IR LED  
C. Camera Din Connector  
D. Camera Lens  
Installation and Adjustment  
A. Camera Installation  
1. Install or mount the camera at the desired  
location. Do not place camera in a location  
subject to direct sunlight or bright light.  
2. The coaxial cable supplied has one end  
with a DIN connector (Male) and the  
opposite end with a DIN connector (Female).  
Slowly insert the DIN plug into the back of  
the camera being careful to align the DIN  
plug correctly.  
3. The camera body could be adjusted up and down by  
loosening screw A and tightening up at desired angle B.  
4. The camera body could be rotated  
around the mounting bracket D. by adjusting screw C for any direction (360 degree).  
 
B. SWITCHER Installation  
1. Connect the adaptor to the adaptor jack [DC IN] and plug it to a wall outlet.  
2. Connect the DIN plug to the output jack, connect the other end to your TV or monitor.  
3. Connect the DIN jack to the camera DIN plug.  
4. After connecting all the cameras; apply DC12V power supply to system, the power  
indication LED will light up and indicate camera number on channel display LED.  
System Features  
A. Connects up to 4 Video Camera  
Adjustable Brightness, Contrast, Saturation, Hue and Sharpness  
B. High Resolution  
860X525 60Hz for NTSC  
860X625 50Hz for PAL  
C. Various Display Modes  
QUAD Mode  
Full Screen Mode  
PIP Screen Mode  
 
1 PIP Screen Mode  
2 PIP Screen Mode  
Auto Sequence Mode  
D. High Performance Freeze Function  
Flicker Free Image Captured  
E. High Performance Zoom Function  
Selectable Zoom Area  
F. Various Overlay Information  
Camera Title  
Real Time and Date  
Alarm/Loss/Motion Message  
G. Provide Various Event Input  
Video Loss Detection  
Motion Detection  
60 Event Report  
Built-in Buzzer  
H. Power Jack Connection  
DC 12V/1A, 2.1mm Jack, Center is positive.  
Description Of Control  
Front panel.  
1. Power Led.  
2. Zoom Led.  
3. Freeze / Auto scan Led.  
4. Ok / Enter button.  
5. Freeze / Auto scan button.  
6. Infrared ray receiver.  
7. Camera 1 button.  
8. Camera 2 button.  
9. Camera 3 button.  
10. Camera 4 button.  
11. Quad / Menu / ESC  
12. Output jack to monitor or TV Video input  
13. - 16. Camera connector  
17. Adapter jack  
 
Functions of Control Buttons  
When each button is pressed, the corresponding LED above the button will be ON.  
1. Press button FREEZE / AUTO for 3 second to get the sequential displays of channel 1,  
channel 2, channel 3, channel 4, and Quad respectively and proceed in cycle. Or press the  
button less than 1 second to freeze the picture on the display, press again to unfreeze.  
2. Press MENU button for 3 second to enter SETUP MENU. This button can also be used as  
EXIT.  
3. Press button  
(C1) to get full screen display for Channel 1. This button can also be used  
to move the cursor up/left while setting the menu.  
4. Press button  
(C2) to get full screen display for Channel 2. This button can also be used  
to move the cursor down/right while setting the menu.  
5. Press button  
(C3) to get full screen display for Channel 3. This button can also be used  
to increase the setup value or move the cursor left while setting the menu.  
6. Press button  
(C4) to get full screen display for Channel 4. This button can also be used  
to decrease the setup value or move cursor in right direction while setting the menu.  
Remote Control  
1. Menu  
2. Freeze  
3. Zoom  
4. Auto  
5. Quad. mode  
6. PIP 2  
7. PIP 1  
8. Separate Camera  
9. Camera 1  
10. Camera 2  
11. Camera 3  
12. Camera 4  
13. Enter  
14. Move up  
15. Move left  
16. Move down  
17. Move right  
 
Remote Control Functions:  
1. MENU button:  
Please see menu setup section.  
2. FREEZE button:  
Press any channel to get full screen display, and then press FREEZE to freeze the picture.  
Press FREEZE again to unfreeze.  
3. ZOOM button:  
Press ZOOM button to achieve zoom in display.  
Press  
buttons to choose zoom area.  
Press Zoom button again to achieve zoom in display.  
Press  
buttons to get full area display or press ZOOM to re-choose zoom area  
4. AUTO button:  
Press AUTO to get the sequential displays of channel 1, channel 2, channel 3, channel 4,  
and Quad respectively and proceed in cycle. Make sure that each channel is in a state of  
ON while setting auto sequence in the menu.  
5. QUAD. button:  
Press QUAD button while in full screen mode display to display pictures in quad.  
6/7. PIP button:  
Press PIP button to get PIP (picture in picture display). Channel 1 is the default for Full  
screen, and Channel 2 is the default for Sub-screen.  
8. Separate cameras button:  
Press to view 2 cameras at same time  
9. Camera 1 button:  
Press to view full screen of camera 1  
10. Camera 2 button:  
Press to view full screen of camera 2  
11. Camera 3 button:  
Press to view full screen of camera 3  
12. Camera 4 button:  
Press to view full screen of camera 4  
Menu Setup  
Press MENU to setup the menu at any mode.  
1. How to set the menu:  
y Press MENU to enter main menu.  
y Press  
buttons to move the highlight  
section and choose the desired section. Press OK  
to enter the desired section. To exit, press MENU  
button again.  
 
A. System setup:  
y Date / Time: Press  
to move the cursor to the  
desired section wish to adjust. Press  
adjust the section.  
to  
y System Format: Choose PAL / NTSC  
y Key lock: To enable / disable button on the system box.  
y Factory reset: To reset to factory default setting.  
y To exit, press MENU button again.  
B. Display setup:  
y Display on screen: To display title / date / time on the  
screen by check the box beside. To disable by  
un-checking the box.  
y Screen position: To adjust camera viewing area by  
adjusting X (horizontal) and Y (vertical). Border color:  
To change the color or camera's border.  
To exit, press MENU button again.  
C. Auto sequence:  
y To enable or disable auto sequence function.  
Each channel can be set to ON or OFF  
respectively. And the switching time can be  
set from 1sec to 99sec..  
y To exit, press MENU button again.  
D. Camera setup:  
y Camera 1: Press  
camera.  
to switch desired  
y Title: Press  
and press  
to move the cursor,  
to adjust character.  
y Press  
to adjust Brightness, Contrast,  
Saturation, Hue and Sharpness.  
y To exit, press MENU button again.  
 
E. Motion setup:  
y Camera 1: Choose desired camera.  
y Detection Time: To enable / disable detection  
of the cameras.  
y Masking area: To disable some area you wish  
not to detect.  
y To exit, press MENU button again.  
F. Event setup & Event report:  
y Loss: If any camera loss its signal, the report will  
go to Event report.  
y Motion: Any motion detected in front of camera,  
the report will go to Event report.  
y Buzzer hold time: To enable or disable buzzer  
function and can be set from OFF to 99 sec..  
y Report hold time: To enable or disable the report  
function and can be set from OFF to 99 sec.  
y 6 pages of "EVENT REPORT" are available in  
this system.  
y Report can be deleted by choosing "YES" on  
LIST CLEAR section.  
y To exit, press MENU button again.  
y Press any button except "OK" on the switch  
box to clear the alarm noise.  
y Alarm / Alarm Polarity: To enable the Power-On  
alarm, all 4 alarm checks should be ticked  
together with Alarm Polarity to be set "High".  
 
Product Specification  
Camera  
Remote Control/Switcher  
Frequency  
N/A  
310/434 MHz (switcher)  
Channel Scan Period  
IR LED  
N/A  
11  
1-99sec (adjustable)  
N/A  
Video Format  
H Resolution  
Operation Temp  
Power Consumption  
Power Supply  
Video Input  
NTSC/PAL  
330 TV Lines  
-10~50oC  
0.22W  
NTSC/PAL  
N/A  
N/A  
100mA  
From Switcher  
N/A  
DC 12V /1AAdapter  
DIN x 4  
Video Output  
Size (mm)  
Accessories  
1 Vp-p/75 ohm  
105x55x86 mm  
60ft Cable for camera  
DIN x 1  
218x202x44 mm  
DC 12V DC/1AAdapter  
Camera Module  
Lens  
6.0mm/ F2.0 Fixed Focus  
1/3'' CMOS  
Image Sensor  
Pixel  
860x525 60Hz (NTSC), 860x625 50Hz (PAL)  
330 TV Lines  
Resolution  
Illumination  
E Shutter Speed  
S/N Ratio  
< 0 LUX w/ F2.0 Fixed Focus (30 feet)  
1/60 to 1/15,000 second  
>48db  
 

Shark Iron S3901WM User Manual
Sharp Computer Accessories PNSV01 User Manual
Sharper Image Oven 8217SI User Manual
Sony Camera Lens SAL70400G2 User Manual
Sony Car Stereo System 70AP User Manual
Sony Cordless Telephone SPP A941 User Manual
Sony DVD Player SBH20 User Manual
Sony TV Converter Box WM FX488 User Manual
Stiga Brush Cutter SB 435 HD User Manual
Sundance Spas Hot Tub Portofino Series User Manual